ASTM C1193 PDF

ASTM C Standard Guide for Use of Joint Sealants. ASTM-C ; Standard Specification for Elastomeric Joint Sealants. 2. ASTM C; Standard Guide for Use of Joint Sealants. B. FEDERAL. This guide describes the use of a cold liquid-applied sealant for joint sealing applications. Including joints on buildings and related adjacent areas, such as.

Author: Nilmaran Kesho
Country: Japan
Language: English (Spanish)
Genre: Photos
Published (Last): 4 September 2018
Pages: 91
PDF File Size: 18.76 Mb
ePub File Size: 11.47 Mb
ISBN: 767-4-60932-292-6
Downloads: 61792
Price: Free* [*Free Regsitration Required]
Uploader: Kall

ASTM C Standard Test Method for Flow Characteristics of Preformed Tape Sealants This test method describes a laboratory procedure for determining the flow characteristics of preformed tape sealants after a specified time, temperature, and load.

ASTM C Standard Test Method for Tack-Free Time of Elastomeric Sealants This test method covers a procedure for the determination of the tack-free time property of single- and multi-component elastomeric sealants commonly used for sealing, caulking, and glazing in buildings and related construction. Refer to for joint seal geometries. Only those properties for which there are industry-agreed-upon minimum acceptable requirements, as determined by available ASTM test methods, are described in this specification.

ASTM C Standard Test Method for Determining Modulus, Tear and Adhesion Properties of Precured Elastomeric Joint Sealants This test method describes a laboratory procedure for measuring modulus, tear, joint movement ability and adhesion properties of applied, Precured Elastomeric Joint Sealants, hereinafter referred to as “applied seal” and if not applied, hereinafter referred to as “seal,” on portland cement mortar as a standard substrate and or other substrates.

ASTM C Standard Guide for Evaluating Failure of Structural Sealant Glazing This guide covers a screening approach to detect failure adhesive or cohesive of a structural sealant in a structural sealant-glazed window, curtain wall, or other similar system.

ASTM C – 00 Standard Guide for Use of Joint Sealants

It is the responsibility of the user of this standard to establish appropriate safety and health practices, awtm determine the applicability of regulatory limitations prior to use.

This section lists ASTM global standards of relevance to the design-engineering community classified in one of three ways: Sealant Standard Test Methods ASTM C a Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants C1139 test method covers an accelerated laboratory procedure to determine if a sample of a joint sealant will stain the substrate when in contract with masonry, concrete, or stone such as marble, limestone, sandstone, and granite.

Such factors as possible unit fogging or primary sealant reaction in a dual-seal system due to volatile components permeating the IG ashm are not considered in this test method.

  AUO G065VN01 PDF

ASTM C Standard Test Method for Staining of Porous Substrate by Joint Sealants This test method covers four types of laboratory tests to determine if a joint sealant has a probability of staining a porous substrate such as marble, limestone, sandstone, and granite. SSG systems typically are either two aastm four sided, glazed with a structural sealant.

This guide provides information useful to design professionals, architects, manufacturers, installers, and others for the design and installation of silicone sealants for protective glazing systems.

Guide C should be consulted for this information. ASTM C Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems This test method covers a laboratory screening procedure for determining the compatibility of liquid-applied structural sealant glazing sealants when in contact with accessories such as dry glazing gaskets, spacers, shims, and setting blocks after exposure to heat and ultraviolet light.

The designer of a joint seal should take the above into consideration when designing and specifying sealants for certain applications. Link to Active This link will always route to the current Active version of the standard.

Including joints on buildings and related adjacent areas, such as plazas, decks, and pavements for vehicular or pedestrian use, and types of construction other than highways and airfield pavements and bridges.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Presently, only a silicone-sealant that is specifically formulated, tested, and marketed as a structural glazing sealant is allowed for structural sealant glazing.

Considering the range of properties of commercially available sealants, the variety of joint designs possible, and the many conditions of use, the information contained herein is general in nature. This method describes both nondestructive and destructive procedures.

Standard Guide for Use of Joint Sealants

ASTM C Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants This test method covers a laboratory procedure for quantitatively measuring the tensile adhesion properties of structural sealants, hereinafter referred to as the “sealant”.

It also provides information on the adhesive bond of the sealants to the tested substrates. This test method is conducted under dead load in a shear mode.

The user of this practice should define the other parameters to be evaluated such as cleaning of the substrate, depth control of the sealant, sealant profile, etc. The values given in parenthesis are provided for information only. This test method also does not in its standard form test the added influence of acids or caustics or other materials that may be in the liquid, in many applications.

  550 JATHAKA KATHA IN SINHALA PDF

ASTM C1193 – 16

Note 1 – This is not a suitable test method for water-base products. Additional properties may be added as ASTM test methods for those properties become available. Cylindrical sealant backing serves one or more of the following functions: They are intended to serve as a water and air barrier.

Historical Version s – view previous versions of standard. The information and guidelines are also useful for those that supply accessories to c193 sealant zstm and for those that install sealants and accessory materials associated with sealant use.

This test method is applicable to self-leveling and non-sag grades of sealant. ASTM C Standard Test Method for Bubbling of One-Part, Elastomeric Solvent-Release Type Sealants This test method covers determination of the degree of bubble formation or surface blistering in one-part, elastomeric solvent-release type sealants when exposed to elevated temperatures.

ASTM C Standard Test Method for Durability of Sealants Exposed to Continuous Immersion in Liquids This test method covers a laboratory procedure that assists in determining the durability of a sealant and its adhesion to a substrate while continuously immersed in a liquid.

This guide provides information useful to design professionals, manufacturers, contractors, and others for the design and installation of a SSG system. For example, a building owner may require a new courthouse building to have an expected design life of 50 years. Therefore, elements of the building’s exterior envelope should, with proper maintenance, be expected to perform for that time period.

This test method is applicable to both gun and knife grades. Information in this guide is primarily applicable to a single and multi-component, cold liquid-applied joint sealant and secondarily to a precured sealant when used with a properly prepared joint opening and substrate surfaces.

Typical designs and considerations can be found in Guide C ASTM C Standard Guide for Substrates Used in Testing Building Seals and Sealants This guide asttm the c119 standard substrates and their recommended surface preparation for use in standard tests of building seals and sealants.