ASTM F146 PDF

F – 80 Standard Test Methods for Fluid Resistance Of Gasket Materials. Designation: F – Standard Test Methods for. Fluid Resistance of Gasket Materials1 This standard is issued under the fixed designation F ; the. ASTM F – 04 Fluid Resistance of Gasket Materials This standard is issued under the fixed designation F ; the number immediately following the.

Author: Kazralmaran Dounos
Country: Gambia
Language: English (Spanish)
Genre: Finance
Published (Last): 4 November 2005
Pages: 460
PDF File Size: 13.89 Mb
ePub File Size: 8.10 Mb
ISBN: 926-6-39438-455-6
Downloads: 66137
Price: Free* [*Free Regsitration Required]
Uploader: Yokora

Change the distilled water used in the test frequently. ASTM International takes no position respecting the validity of any patent rights asserted in connection with asmt item mentioned in this standard. F — 04 Standard Test Methods for Fluid Resistance of Gasket Materials1 This standard is issued under the fixed designation F ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

For aetm having less than specific gravity 1.

Please help us to share our service with your friends. We need your help to maintenance this website. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability xstm regulatory limitations prior to use.

The results of these test methods are not intended to give any direct correlation with service conditions in view of the wide variations in temperature and special uses encountered in gasket applications.

BoxTrenton, NJ Exercise care when removing the excess fluid so that no squeezing action occurs on the sample.

Temperature of Test Measurement 7. Last previous edition approved in as F — These test methods are applicable to ethylene glycol, propylene glycol, commercial coolants and blends with water thereof see Note 1water, and other commercial oils and fuels.

The user should be aware that results may differ. Measure the weight of the test specimen to the nearest 1 mg 0.

ASTM F – 12 Standard Test Methods for Fluid Resistance of Gasket Materials

It is understood that the results will be reported per D along with the specific immersion conditions used prior to said adhesion test. Thank you for interesting in our services. If such information is not available, then the material should be tested by itself in fresh fluid to determine compatibility with said fluid.

  ABDULLAH AYSU PDF

zstm

This gives the final volume, V2. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

ASTM F146 – 12

The specific sstm fluids and test conditions outlined were selected as typical for purposes of comparing different materials and can be used as a routine test when zstm upon between the purchaser and the manufacturer. If g146 feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. The specific test fluids and test conditions outlined were selected as typical for purposes of comparing different materials and can be used as a routine test when agreed upon between the purchaser and the manufacturer.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. It is designed for testing specimens cut from gasketing materials or from finished articles of commerce. Please fill this form, we will try to respond as soon as possible.

The inch-pound units in parentheses aztm for information only. Link to Active This link will always route to the current Active version of the standard.

A superscript epsilon e indicates an editorial change since the last revision or reapproval. Insert the aluminum-foil covered stoppers into the test tubes before placing them in the supporting rack within the oven. After immersing the specimens aetm the various test fluids, the effect on physical properties is expressed as change in tensile strength, compressibility in softened condition, flexibility, volume change, and thickness and weight changes from the original condition.

Dead weight loads are listed in Table 1.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Graduate the dial in 0. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn. Asym anvil shall have a diameter not less xstm that of the presser foot, which has a diameter of 6.

  ANNUARIO PONTIFICIO 2012 PDF

The change in weight of the specimens is to be calculated as an expression of percentage change on the original weight. Take a sufficient number of readings, depending on the size of the specimen, to provide a reliable average value. NOTE 2—Great care must be taken to record the swollen thickness when the needle slows to a different rate which reflects indentation into the softened specimen. Originally approved in Refer to Test Method D for further information regarding immersion test fluids.

ICS Number Code The producer must be aware that different coolant r146 may yield different results. These test methods are not applicable to the testing of vulcanized rubber, a procedure that is described in Test Method D Size px x x x x Pour enough fresh test fluid over the specimens to ensure that the specimens are wetted and covered by the fluid.

A number in parentheses indicates the year of last reapproval. The inch-pound units in parentheses are for information only. Significance and Use 4.

Then withdraw the specimens from the cooled-down test fluid and immediately blot the samples with sheets of blotting paper ashm remove excess liquid from the surfaces. These test methods are not applicable to the testing of vulcanized rubber, a procedure that is described in Test Method D NOTE 1—Coolant mixtures are typically tested under boiling reflux conditions. Historical Version s – view previous versions of standard. Summary of Test Methods 3. Please copy and paste this embed script to where you want to embed Embed Script.