RZNC make DSP as the core control system,High-speed processing operation sports concluding continuous, step (crawl), distance, manual operation. Diagram. RZNC Connection Board. PDF created with FinePrint pdfFactory Pro trial version With DSP technology, the increase of cut-to-length precision can be obtained as it offers well-timed The RZNC Working Video links: . Press the “Delete” key,the RZNC Controller will showing “manual state screen”(as View 2). View 2.

Author: Zuzil Mesho
Country: Turks & Caicos Islands
Language: English (Spanish)
Genre: Politics
Published (Last): 21 May 2016
Pages: 40
PDF File Size: 13.39 Mb
ePub File Size: 18.99 Mb
ISBN: 874-4-51755-136-1
Downloads: 13637
Price: Free* [*Free Regsitration Required]
Uploader: Vohn

RZNC-0501 DSP Operating Manual

New three-axis linkage motion mode to achieve comprehensive controlling 2. The condition for Stop point process is that the 3 axes must have homed before saving the stop point.

Leave your dps the “ok” key when the DSP handle screen is light on 4. So the rea l proces s s peed is: Auto process operating steps are: Identifies M code, F code and other development commands, can open a special code based on user needs. Dear all, Can anyone help us to solve this issue Press the “ok” key then power on with the computer. It refe rs to the Height tha t Z axis ca n go up.

If it does not need to cha nge, press exit and go back former menu. Large storage space, perfect U disk compatibility, fast reading speed, safe and reliable U disk-processing. The operating steps are: Before running any file, the machine and system parameters should be set correctly.

Easily process G code or PLT file with super size; 4. Re p r e s s to save the change and it togoes ba ck the f ormer menu. U disk fil e and Inner file. Support intelligent file checking function.


There are 6 stop points totally. Stop position is Machinery coordinate position and has nothing to do with working coordinate. Do you have any suggestion to solve my problem? Home Speed refers to that 3 axes home speed, normally Z axis home speed should be lower than that of X and Y axes. The system will automatically protect the process data when the power fall down suddenly.

If it does not need to cha nge, p res s to exit and go back former menu. P r e s s the s creen shows: If you had right to dothe DSP screen will show you this: It supports high micro step which makes precise and fast process possible; 7. D is to set Z axis working origin. Also the DSP controller Manual can be sent for free here, welcome to contact us. Home position depends on home sensor. Comes with Nanual communications port, file transfer efficiency can be directly read U disk, card reader file, Plug and Play.

Help! I deleted the firmware from my DSP controller – Page 5

Strong system and process file examining function; 5. Totally independent from PC platform. Dsp a11 handle controller operating manual rico cnc Technology.

After the machine goes home, the system is in manual process, which shown as below: Pres s to save changeto cancel the setting and goback former menu. Then you must change your file size or operate it in an other engraving machine with bigger table size. Pres s toto go to first line whileq u i t v i e w.

If it d oes not need to cha nge, pressexit and go back former menu. The setting means of High speed is the same to Low speed. System can support automatic dynamic upgrades, convenient to remote operation, remote maintenance.


If it unneces sa ry to cha nge it, pres s till it goes back former menu.

Easily process G code or PLT The maual mode is: I cannot follow Alan’ instructions because it does not give me control and i can’t move Z axis by hand.

Reliable data protection and recover function; 9. If it does not need to cha nge, press till it goes back former menu. Its va lue cannot exceed 1mm. Author Index Acharya BC Set proces s pa ra metersa nd foll owin g steps a re s imila r with the a uto p rocess. If it does not need to cha nge, press former menu. The screen displays as below: U disk file refers to files sa ved in U disk. Please help me in this regard. Pres sto confirm and save the changes to give up thea nd it goes ba ck the f ormer menu, presschanges and goes back the former menu.

I send you here the parameters of my machine and the dsp, hope if anyone can help me!!! Then Press to clear X and Y axes working origin; and press toclear Z axis working origin. I deleted the firmware from my DSP controller.