JIS G Carbon steels for cold heading — Part 1: Wire rods (Foreign Standard). standard by Japanese Industrial Standard. ) G Cold heading quality carbon steel – Section 1: Wire rods 5 . Table of composition for JIS wire rods and secondary processed products of. Carbon steels for cold heading. Part 1: Wire rods. SWRCH 6A to 22A. 10K to 50K. JIS G Nuts and bolts, small screws, small tacks, and other various.
|Published (Last):||26 March 2016|
|PDF File Size:||15.88 Mb|
|ePub File Size:||8.86 Mb|
|Price:||Free* [*Free Regsitration Required]|
However, in the case by processes other than process D and process DA, they shall be subjected to the agreement between the purchaser and the supplier. However, manufacturing processes other than given above may be selected by agreement between the purchaser and the supplier. Wire rods JIS Z However, those of wires of 32 mm or over in wire diameter shall be as agreed upon between the purchaser and the supplier. Por60ns given sidelines are the matters in which the contents of the original International Standard have been modified.
Table 5 Tolerances on wire diameter and ovality Unit: Over 5 to and incl. Over 3 to and incl. The depth of flaws shall conform to table 6 for killed steel including aluminum-killed steen.
The process DA means a process wherein wire rods having been cold worked are annealed and further finished by cold working or a process wherein wire rods are finished by cold working after annealing.
When the flaw depth is especially requested to be eontrolled for 15 mm max. Carbon steels for cold heading — Part g350-1 Table 4 Permissible limits of mean depth of decarhurized layer unIt: Over 4 to and incl. The relevant Minister and the Japanese Industrial Standards Committee are not responsible for identifYing the patent right, application for a patent after opening to the public, utility model right or application jix registration of utility model after opening to the public which have the said.
Two wires are shown below, carrying 3. Attention is drawn to the possibility that some parts of this Standard jjis conflict with a patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have technical properties.
B inspection certificate 3. Documents Flashcards Grammar checker. Note 4 The ovality means the difference between the maximum and the minimum wire diameters measured in the same cross-section.
Over 3 to and incL 6 Over 6 to and incL 10 Over 10 to and inel. Wires Date of Establishment: Further, whether test piece of No.
JIS G Carbon steels for cold heading –
JIS G English: June 20, 1. However, in the case where a flaw depth in necessitated to be especially controlled, they shall conform to table 7 subject to the agreement between the purchaser and the supplier. In that case, the carburized layer depth measured at four positions by equally dividing the circumference adopting the position of the maximum decarburized layer depth as an origin, and the mean value thereof 3g507-1 be obtained. For the tensile test, t No.
JIS G 3507-2: Carbon steels for cold heading –
A list of modifications with the explanations is given in annex 1 informative. Some of the items below, however, may be omitted, if agreed between the purchaser and the supplier. Over 25 to and incl.
Over 4 to and inc!. Wires Introduction This Japanese Industrial Standard has been prepared based on the second edition of ISO Steels for cold heading a11d cold extruding published in with some modifications of the technical contents.
Procedures of the investigation. JIS G consists of the following 2 parts under the general title” Carbon steels for cold heading”: Wire rods Part 2: Carbon steels for cold heading – advertisement.
Over 5 min. Over 15 to and incl. No parl of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, vvithout pennission in wriling from the publisher. The most recent editions of the standards including the amendments shall be applied. Informative Hardness HRB 45 min. For those of diameter 3 mm or less, the reduction of area is not specified.
Table 6 Surface flaw depth of killed steel Unit: The sample product shall be measured for surface g35007-1 depth with a measuring device having an appropriate precision. Over 4 to and incL 5 min.