ARMY TM &P* AIR FORCE TO 11W TECHNICAL M68 SIGHT, REFLEX, W/QUICK RELEASE MOUNT AND SIGHT MOUNT M68 Cco Tm Manual Army – p s – scribd TM. CHAPTER I. PRESENTATION. Aimpoint CompM4 Reflex Sight is a rugged precision red dot Sight developed mainly for military and law enforcement. M68 SIGHT, REFLEX, W/QUICK RELEASE MOUNT AND SIGHT MOUNT CLOSE COMBAT OPTIC (CCO) (NSN ) (NSN ).

Author: Tezil Fegis
Country: Philippines
Language: English (Spanish)
Genre: Finance
Published (Last): 11 November 2016
Pages: 173
PDF File Size: 18.22 Mb
ePub File Size: 11.48 Mb
ISBN: 741-5-56425-850-5
Downloads: 96894
Price: Free* [*Free Regsitration Required]
Uploader: Tauzuru

If necessary, you can also run water through the honeycomb to clear it. Before After Before AfterSight7. Integral mount that eliminates the separate ring, and can be customized with vertical and forward spacers to fit a variety of weapon systems. When mounting on the M16A2 rifle, the special shaped spacer is removed.

Close front and rear lens covers cvo and turn switch knob 1 counterclockwise to OFF position when cfo sight is not being used.

It is a reflex sight, designed to be parallax free past fifty meters. This listing is for informational only and is not authority to requisition the listed items. Remove Cap Battery 1 by turning it counterclockwise.

Who can install, replace, or use the item.

The recoverability code is shown in the fifth position of the SMR code as follows: If the third position of the SMR code authorizes you to replace the item, but the source code indicates the item is assembled at a higher level, order the item from the higher level of maintenance. An “F” appearing in the fourth position of the SMR code indicates complete repair is possible at the field maintenance level.


NOTE The M68 Comp M2 sight uses lithium-manganese dioxide batteries which, when depleted, are to be disposed of in accordance with technical bulletin, TBbattery disposition and disposal, paraand local regulations and procedures contact your local defense reutilization and marketing office DRMO for assistance.

Condemnation and disposal of item are not authorized below depot level. Tj the flats of two fingers, press against the front of ARD 2 and rotate counterclockwise until the ARD is removed. Learning to coc this TM is as easy as reading through the next few pages of this section. The serial number is located on the bottom of the sight. It authorizes the requisitioning, issue, and disposition of spares, repair parts, and special tools as indicated by the source, maintenance, and recoverability SMR codes.

The item number is the number assigned to the item as it appears in the figure referenced in the adjacent figure number column.

Column 3 Maintenance Function. The m688 follows the horizontal and vertical movement of the gunners eye while remaining fixed on the target. The last position is the extra high intensity setting.

The M68 Close Combat Optic |

Before immersing the sight in water or using it in the rain, verify that the caps are snug by hand tightening them. The battery life of the least preferred batteries will be less than half that of the preferred batteries. Using the flats j68 two fingers, press against the front of ARD 2 and rotate counterclockwise approximately turn until you hear a slight click and the ARD is level in the front of the sight. The second cause is the absence of the rubber O-ring, which degrades the positive connection with the battery.


To verify serviceability by measuring the mechanical, pneumatic, hydraulic, or electrical characteristics of an item and comparing those characteristics with prescribed standards on a scheduled basis, i.

Army Publishing Directorate

Remember, this TM has been arranged with you, the user, in mind. If the spring connector becomes corroded, clean it with a wire brush.

Column 3 lists the functions to be performed on the item listed in column 2. Name or identification of the tool or test equipment. Energizer A is the commercial equivalent to the NSN listed. Improving battery life to 30 times at the same dot brightness.

Failure to observe these precautions could result in serious injury or death to personnel. Using the table of contents, determine the assembly group to which the item belongs.

The M68 Close Combat Optic

Column 2 – Remarks. The maintenance code entered in the third position will indicate authorization to the following levels of maintenance: Leave a Reply Cancel reply Cco must be logged in to post a comment.

Insert O-ring 3 around the adjustment screw housing 2. There are two configurations: